Ketahanan n-pentana dan sifat mekanis vulkanisat karet perapat dari campuran karet alam/akrilonitril-butadiena dengan kompatibiliser
Abstract
The improvement of the compatibility of natural rubber (NR)/acrilonitrile-butadiene rubber (NBR) blend on rubber seal vulcanizate has been done by the addition of chloroprene rubber (CR) or epoxidized natural rubber (ENR) as compatibilizer. Rubber seal compound was made of NR and NBR blend (BN) with CR (BCR), and ENR with epoxy content of 10% (BENR10), 20% (BENR20), 30% (BENR30), 40% (BENR40), and 50% (BENR50). The composition in each formula was homogenized, with comparison of NR:NBR at 40:60, and NR:compatibilizer:NBR at 40:5:55. That compounds were vulcanized with efficient system at 150oC. The addition of CR-compatilizer improved the curing characteristic, compression set, and n-pentane resistance of BN vulcanizate. Meanwhile, the addition of KAE-compatilizer improved the elasticity of BN vulcanizate. BENR elasticity and n-pentane resistance increased in line with the increasing level of epoxy content of ENR.
Keywords: rubber seal, compatibilizer, n-pentane resistance, mechanical properties.
Full Text:
PDFReferences
Acharya, H., Kuila, T., Srivastava, S. K., & Bhowmick, A. K. (2008). Effect of layered silicate on EPDM/EVA blend nanocomposite: Dynamic mechanical, thermal, and swelling properties. Polymer Composites, 29(4), 443-450,
http://dx.doi.org/10.1002/pc.20433
Brandrup, J., Immergut, E. H., & Grulke, E. A. (1998). Polymer Handbook. New York, USA: Wiley.
Choi, S., & Ha, S. (2009). Influence of the swelling temperature and acrylonitrile content of NBR on the water swelling behaviors of silica-filled NBR vulcanizates. Journal of Industrial and Engineering Chemistry, 15, 167-170,
http://dx.doi.org/10.1016/j.jiec.2008.09.016
Chonkaew, W., Mingvanish, W., Kungliean, U., Rochanawipart, N., & Brostow, W. (2011). Vulcanization characteristics and dynamic mechanical behavior of natural rubber reinforced with silane modified silica. Journal of Nanoscience and Na-notechnology, 10, 1–7,
http://dx.doi.org/10.1166/jnn.2011.3563
Corish, P. J. (1967). Fundamental studies of rubber blends. Rubber Chemical Technology, 41, 324-340, http://dx.doi.org/10.5254/1.3539049
de Silva, K. G., & Lewan, M. (1998a). Improving the morphology and properties of NR/NBR blends with NR/PMMA graft copolymers. In Tinker, A.J. & Jones, K.P (Eds.), Blends of Natural Rubber: Novel Techniques for Blending with Speciality Polymers (1st ed., pp. 68-78). Chapman & Hall, London: Springer Science+Business Media Dordrecht.
de Silva, K. G., & Lewan, M. (1998b). Improving phase morphology and properties of NR/NBR blends with compatibilizers. Journal of the Rubber Research Institute of Sri Lanka, 81, 38-50
Gelling, I. R. (1991). Epoxidized natural rubber. Journal of Natural Rubber Research, 6(3), 184-205.
Gonzalez, L., Rodrıguez, A., Del Campo, A., & Marcos-Fernandez, A. (2002). Crosslink reaction of natural rubber with thiuram sulphur donors in the presence of a thiuram monosulfide. Journal of Applied Polymer Science, 85, 491-499,
http://dx.doi.org/10.1002/app.10438
Ismail, H., Ahmad, Z., & Mohd, I. Z. A. (2001). Comparison of cetyltrimethyl ammonium maleate and sulphenamide as an accelerator in carbon black filled natural rubber compounds. Polymer Testing, 20, 607-614, http://dx.doi.org/10.1016/S0142-9418(00)00082-9
Ismail, H., Ishak, S., & Hamid, Z. A. A. (2015). Effect of blend ratio on cure characteristics, tensile properties, thermal and swelling properties of mica-filled (ethylene-propylene-diene monomer)/ (recycledethylene-propylene-diene monomer) (EPDM/R-EPDM) blends. Journal of Vinyl & Additive Technology, 21(1), 1-6,
http://dx.doi.org/10.1002/vnl.21369
Ismail, H., Rohani, & Taib, R. M. (2014). Effects of dynamic vulcanization on tensile, morphological, and swelling properties of poly (vinyl chloride) (PVC)/epoxidized naturalrubber (ENR)/(kenaf core powder) composites. Journal of Vinyl & Additive Technology, 1-7,
http://dx.doi.org/10.1002/vnl.21401
Kinasih, N. A., & Fathurrohman, M. I. (2015a). Pe-ngaruh kondisi reaksi terhadap karakteristik ketananan n-pentana pada karet alam epoksi. Manuscript sumbitted for publication.
Kinasih, N. A., Fathurrohman, M. I., & Suparto, D. (2015b). Pengaruh suhu vulkanisasi terhadap sifat mekanis vulkanisat karet alam dan karet akrilonitril-butadiena. Majalah Kulit, Karet, dan Plastik, 31(2), 65-74,
http://dx.doi.org/10.20543/mkkp.v31i2.504
Kinasih, N. A., & Fathurrohman, M. I. (2015c). Effect of curing systems on mechanical properties and n-pentane resistance of carbon black filled natural rubber vulcanizates. Manuscript sumbitted for publication.
Klattanavith, N. (1988). Study of the oil-resistance of natural rubber. Journal of National Research Council of Thailand, 20(2), 1-7.
Kongsin, K., & Lewan, M. (1998). Improving the morphology and properties of NR/NBR blends with polychloroprene as the compatibilizing agent. In Tinker, A.J. & Jones, K.P (Eds.), Blends of Natural Rubber: Novel Techniques for Blending with Speciality Polymers (1st ed., pp. 80-93). Chapman & Hall, London: Springer Science Business Media Dordrecht.
Lawandy, S. N., Botros, S. H. & Mounir, A. (1993). Effect of vulcanizing agent concentration on the swelling behavior of chloroprene rubber under compression strain. Polymer-Plastics Technology and Engineering, 32(3), 223-235,
http://dx.doi.org/10.1080/03602559308019229
Manoj, K. C., Kumari, P., & Unnikrishnan, G. (2011). Cure characteristics, swelling behaviors, and mechanical properties of carbon black filler reinforced EPDM/NBR blend system. Journal of Applied Polymer Science, 120, 2654–2662,
http://dx.doi.org/10.1002/app.33476
Marković, G., Marinović-Cincović, M., Jovanović, V., Samaržija-Jovanović, S., & Budinski-Simendić. (2013). NR/CSM/biogenic silica rubber blend composites. Composites Part B: Engineering, 55, 368-373, http://dx.doi.org/10.1016/j.compositesb.2013.06.045
Mathew, S., Brahmakumar, M., & Abraham, T. E. (2006). Microstructural imaging and characterization of the mechanical, chemical, thermal, and swelling properties of starch–chitosan blend films. Biopolymers, 82, 176–187,
http://dx.doi.org/10.1002/bip.20480
Noriman, N. Z., Ismail, H. & Rashid, A. A. (2010). Characterization of styrene butadiene rubber/recycled acrylonitrile-butadiene rubber (SBR/NBRr) blends: The effects of epoxidized natural rubber (ENR-50) as a compatibilizer. Polymer Testing, 29, 200–208, http://dx.doi.org/10.1016/j.polymertesting.2009.11.002
Obasi, H. C., Ognobe, O. & Igwe, I. O. (2009). Diffusion characteristics of toluene into natural rubber/linear low density polyethylene blends. International Journal of Polymer Science, 1-6, http://dx.doi.org/10.1155/2009/140682
Onyeagoro, G. N. (2012). Effect of zinc oxide level and blend ratio on vulcanizate properties of blend of natural rubber and acrylonitrile-butadiene rubber in the presence of epoxidized natural rubber. Academic Research International, 3(1), 499-509.
Palaty, S. & Joseph, R. (2001). Studies on xanthate-zinc diethyl dithiocarbamate accelerator combination in natural rubber. Plastics Rubber and Composites, 30, 270-274,
http://dx.doi.org/10.1179/146580101101541697
Phinyocheep, P., & Boonjairik, K. (2006). Investigation on hydrogenation and epoxidation of natural rubber in latex stage. Proceedings of International Rubber Conference. Lyon, France.
Prakashan, K., Gupta, A. K., & Maiti, S. N. (2007). Effect of compatibilizer on micromechanical deformations and morphology of dispersionin PP/PDMS blend. Journal of Applied Polymer Science, 105, 2858–2867,
http://dx.doi.org/10.1002/app.26510
Rajasekar, R., Pal, K., Heinric, G., Das, A., & Das, C.K. (2009). Development of nitrile butadiene rubber–nanoclay composites with epoxidized natural rubber as compatibilizer. Materials and Design, 30, 3839–3845,
http://dx.doi.org/10.1016/j.matdes.2009.03.014
Ramesan, M. T., Alex, R., & Khanh, N. V. (2005). Studies on the cure and mechanical properties of blends of natural rubber with dichlorocarbene modified styrene–butadiene rubber and chloroprene rubber. Reactive & Functional Polymers, 62, 41–50, http://dx.doi.org/10.1016/j.reactfunctpolym.2004.08.002
Sahakaro, K., Pongpaibon, C., & Nakason, C. (2009). Improved mechanical properties of NR/EPDM blends by controlling the migration of curative and filler via reactive processing technique. Journal of Applied PolymerScience, 111, 2035-2043, http://dx.doi.org/10.1002/app.29193
Setua, D. K. & Gupta, Y. N. (2007). On the use of micro thermal analysis to characterize compatibility of nitrile rubber blends. Thermochimica Acta, 462, 32–37,
http://dx.doi.org/10.1016/j.tca.2007.06.004
Sommer, J. G. (2009). Engineered Rubber Products: Introduction to Design, Manufacture and Testing. Munchen, Jerman: Carl Hanser Verlag,
http://dx.doi.org/10.3139/9783446433441
Tanrattanakul, V., Wattanathai, B., Tiangjunya, A., Muhamud, P. (2003). In situ epoxidized natural rubber: improved oil resistance of natural rubber. Journal of Applied Polymer Science, 90, 261–269, http://dx.doi.org/10.1002/app.12706
Teh, P. L., Ishak, Z. A. M., Hashim, S. Karger-Kocsis, J., & Ishiaku, U.S. (2004). Effects of epoxidized natural rubber as a compatibilizer in melt compounded natural rubber-organo clay nanocomposites. European Polymer Journal, 40, 2513-2521, http://dx.doi.org/10.1016/j.eurpolymj.2004.06.025
Thomas, S. P., Mathew, E .J. & Marykutty, C.V. (2012). Nano modified fillers in chloroprene-rubber compatibilized natural rubber/acrylonitrile–butadiene rubber blends. Journal of Applied Polymer Science, 124, 4259–4267,
http://dx.doi.org/10.1002/app.12706
Thomas, S. P., Thomas, S, Marykutty, C. V, & Mathew, E. J. (2013). Evaluation of effect of various nanofillers on technological properties of NBR/NR blend vulcanized using BIAT-CBS. Journal of Polymer, 2013, 1-10,
http://dx.doi.org/10.1155/2013/798232
Tosaka, M. (2007). Strain-induced crystallization of crosslinked natural rubber as revealed by X-ray diffraction using synchrotron radiation. Polymer Journal, 39(12), 1207-1220,
http://dx.doi.org/10.1295/polymj.PJ2007059
Vallim, M. R., Araujo, J. R., Spinace´, M. A. S., & De Paoli, M. A. (2009). Polyamide-6/high-density polyethylene blend using recycled high-density polyethylene as compatibilizer: Morphology, mechanical properties, and thermal stability. Polymer Engineering and Science, 49(10), 2005-2014, http://dx.doi.org/10.1002/pen.21439
Van Duin, M., & Dikland, H. (2007). A chemical modification approach for improving the oil resistance of ethylene propylene copolymer. Polymer Degradation and Stability, 92, 2287-2293, http://dx.doi.org/10.1016/j.polymdegradstab.2007.04.018
Varghese, H., Bhagawan, S. S., Rao, S. S., & Thomas, S. (1995). Morphology, mechanical and viscoelastic behaviour of blends of nitrile rubber and ethylene-vinyl acetate copolymer. European Polymer Journal, 31(10), 957-967,
http://dx.doi.org/10.1016/0014-3057(95)00056-9
Varughese, S., & Tripathy, D. K. (1992). Dynamic mechanical properties of epoxidised natural rubber vulcanisates: Effect of curing system and ageing. Polymer Degradation and Stability, 38, 7-14, http://dx.doi.org/10.1016/0141-3910(92)90016-X
Wang, H., Lu, X., & Wang, S. (2014). The swelling properties of nitrile rubber with different acrylonitrile contents in cyclohexane medium research. Advanced Materials Research, 936, 942-1947, http://dx.doi.org/10.4028/www.scientific.net/amr.936.1942
Wu, Y., Yang, Y., Li, B., & Han, Y. (2006). Reactive blending of modified polypropylene and polyamide 12: Effects of compatibilizer content on crystallization and blend morphology. Journal of Applied Polymer Science, 100, 3187–3192,
http://dx.doi.org/10.1002/app.23572
Xie, L., Jiang, M., Dong, X., Bai, X., Tong, J., & Zhou, J. (2012). Controlled mechanical and swelling properties of poly (vinyl alcohol)/sodium alginate blend hydrogels prepared by freeze–thaw followed by Ca2+ crosslinking. Journal of Applied Polymer Science, 124, 823–831,
http://dx.doi.org/10.1002/app.35083
Yahya, R. Y. S, Azura, A. R. & Ahmad, Z. (2011). Effect of curing systems on thermal degradation behaviour of natural rubber (SMR CV 60). Journal of Physical Science, 22(2), 1–14.
Yong, M. K., Ismail, H., & Ariff, Z. M. (2007). The effect of epoxidized natural rubber (ENR-50) or polyethylene acrylic acid (PEA) as compatibilizer on properties of ethylene vinyl acetate (EVA)/natural rubber (SMR L) blends. Polymer-Plastics Technology and Engineering, 46, 1001–1009, http://dx.doi.org/10.1080/03602550701519480
Yu, L., Dean, K., Yuan, Q., Chen, L., & Zhang, X. (2007). Effect of compatibilizer distribution on the blendsof starch/biodegradable polyesters. Journal of Applied Polymer Science, 103, 812–818,
http://dx.doi.org/10.1002/app.25184
No comments:
Post a Comment